undefined
+
  • undefined

YRD-100B/YRD-160 drive shaft balancing machine

The YRD-100B/YRD-160 type drive shaft balancing machine is a hard support structure, and the drive head drives the drive shaft to run, which is a universal two-swing frame. It is suitable for the single drive shaft dynamic balance of cars and trucks. This model is widely used in the drive shaft maintenance industry.

Key words:

YRD-100B/YRD-160 drive shaft balancing machine

  • Product Description
  • Scope of application
  • Technical parameters
  • Product Video
  • File Download
    • Commodity name: YRD-100B/YRD-160 drive shaft balancing machine

    The YRD-100B/YRD-160 type drive shaft balancing machine is a hard support structure, and the drive head drives the drive shaft to run, which is a universal two-swing frame. It is suitable for the single drive shaft dynamic balance of cars and trucks. This model is widely used in the drive shaft maintenance industry.

    The YRD-100 type drive shaft balancing machine is a special balancing machine for checking the dynamic balance of the automobile drive shaft. It has three models of A, B and D.

    The A- type machine has three supporting frames, which can realize two-sided or three-sided verification of the transmission shaft. The three-point center frame on the middle swing frame of the machine is used for balancing the double transmission shaft. By adjusting the three supporting screws and combining with the "centering V-plate", the middle bearing can be firmly supported and centered to meet the requirements of dynamic balance. The transmission head on the right swing frame can be axially expanded and contracted by using the operating handle. The unbalance and phase angle position of the left, middle and right correction surfaces can be automatically measured and memorized.

    Type B machine has two support frames, the weight range of the measured transmission shaft workpiece is large, the right support frame is fixed by the pneumatic mechanism to lock or loosen, the operation is simple;

    D type machine is a special four swing frame, that is, three shaft tube assembly shaft balance and development and design of special balancing machine.

    The YRD-100B/YRD-160 type drive shaft balancing machine is a hard support structure, and the drive head drives the drive shaft to run, which is a universal two-swing frame. It is suitable for the single drive shaft dynamic balance of cars and trucks. This model is widely used in the drive shaft maintenance industry.

    The machine supporting electrical measurement system has ZL220 embedded system and ZL-2 industrial computer system. It has the characteristics of high precision, high efficiency, simple operation, intuitive display and strong human-computer interaction ability. Before starting up, as long as the known parameters such as the size of the two correction surfaces of the rotor and the radius of the correction surface are input to the electrical measuring box, the size and phase of the imbalance can be displayed after the rotor is started to rotate.

  • drive shaft

  • YRD-100B

    Workpiece quality range

    10~100kg

    Maximum length of workpiece

    2300mm

    Unbalance Reduction Rate URR

    90%

    Maximum diameter of workpiece

    φ130mm

    Maximum initial unbalance of workpiece

    <500g · cm

    Minimum detection amount

    2g · cm

    Balance speed

    800、1200、1600、2400r/min

    YRD-160

    Workpiece quality range

    10~160kg

    Maximum length of workpiece

    2300mm

    Unbalance reduction rate

    90%

    Maximum diameter of workpiece

    φ130mm

    Maximum initial unbalance of workpiece

    ≤ 800g · cm

    Minimum detection amount

    2g · cm

    Balance speed

    800、1200、1600、2400r/min

     

    Note:

    1. The specifications in the table are standard models, and the special requirements in the specifications shall be negotiated separately;

    2. The speed in the table is approximate reference value;

    3. The manufacturer reserves the right to modify the parameters of the table column. If there is any change, no further notice will be given.

The YRD-100 type drive shaft balancing machine is a special balancing machine for checking the dynamic balance of the automobile drive shaft. It has three models of A, B and D.

The A- type machine has three supporting frames, which can realize two-sided or three-sided verification of the transmission shaft. The three-point center frame on the middle swing frame of the machine is used for balancing the double transmission shaft. By adjusting the three supporting screws and combining with the "centering V-plate", the middle bearing can be firmly supported and centered to meet the requirements of dynamic balance. The transmission head on the right swing frame can be axially expanded and contracted by using the operating handle. The unbalance and phase angle position of the left, middle and right correction surfaces can be automatically measured and memorized.

Type B machine has two support frames, the weight range of the measured transmission shaft workpiece is large, the right support frame is fixed by the pneumatic mechanism to lock or loosen, the operation is simple;

D type machine is a special four swing frame, that is, three shaft tube assembly shaft balance and development and design of special balancing machine.

The YRD-100B/YRD-160 type drive shaft balancing machine is a hard support structure, and the drive head drives the drive shaft to run, which is a universal two-swing frame. It is suitable for the single drive shaft dynamic balance of cars and trucks. This model is widely used in the drive shaft maintenance industry.

The machine supporting electrical measurement system has ZL220 embedded system and ZL-2 industrial computer system. It has the characteristics of high precision, high efficiency, simple operation, intuitive display and strong human-computer interaction ability. Before starting up, as long as the known parameters such as the size of the two correction surfaces of the rotor and the radius of the correction surface are input to the electrical measuring box, the size and phase of the imbalance can be displayed after the rotor is started to rotate.

Online Inquiry

Related Products

Free consultation professional answer
Leave your contact information and we will contact you as soon as possible for free professional answers.

Submit Message
Customer Service