The ZLAS-1 is a single-sided vertical full-automatic de-balancing machine that achieves workpiece balance correction by de-weighing according to the customer's workpiece design requirements. Products are divided into drilling, milling and turning according to the weight removal method (turning products are introduced separately); Single station is to complete measurement, correction and re-inspection on one station, with high one-time weight removal rate. The upper and lower workpieces are completed manually. The weight removal is on an independent station, and the dynamic balance efficiency of the equipment is 70% higher than that of manual weight removal. The product is suitable for leveling and automatic calibration of disc parts such as brake discs, pulleys, brake hubs, clutches, flywheels, etc.

The drive motor presses the rotor through a flat belt, and the belt is placed in the middle of the rotor. The balancing machine is equipped with a drilling and weight removal device, which is controlled by PLC. The beam moves 800mm left and right, the drill bit is located directly above the workpiece, and the diameter of the drill bit is 20mm; After the balancing machine is detected, the punching position will automatically stop directly above, and the punching and weight removal will be carried out on the two measuring surfaces respectively.

YLD-11 vertical balancing machine is a more advanced vertical hard bearing balancing machine. It is suitable for the calibration of dynamic balancing machine for automobile and motorcycle accessories. Such as clutch pressure plate, flywheel, gear, pulley and other disc parts. This series of equipment has standard, type A, type B and other three configurations.

With the development of precision and high speed of rotating machinery, YYW-500 hard bearing balancing machine is very important to reduce vibration, reduce noise, prolong the service life of machinery and improve the safety performance of machinery. Therefore, the dynamic balance of rotating machinery is an essential process, and the YYW-500 balancing machine is a kind of universal balancing machine with a wide range of uses.

YLD-3/YLD-5 vertical balancing machine is a more advanced vertical hard bearing balancing machine. It is suitable for the calibration of dynamic balancing machine for automobile and motorcycle accessories. Such as clutch pressure plate, flywheel, gear, pulley and other disc parts. This series of equipment has standard, type A, type B and other three configurations.

Balanced workpiece mass range 100-3000kg workpiece maximum diameter 3000mm workpiece support shaft diameter range Φ40-260mm two support center minimum distance 300mm coupling end face to right support seat maximum distance 3000mm.

YYWQ-300 double-drive balancing machine This machine lengthened the base and added a ring belt transmission device on the basis of the general-purpose hard-bearing balancing machine YYW-300. The electric measuring system can be equipped with an advanced ZL-220 digital display electric measuring box. The electric box adopts large-scale integrated circuits and is programmed for operation. Its measurement speed is fast, and the display is stable, accurate and intuitive. The size and phase of the unbalance can be measured in a short time, and the size and phase of the unbalance can be directly displayed in grams and angles at the same time, and the weight can be switched after the rotor stops rotating.

YYW-3000 hard bearing balancing machine is a set of precision machinery and modern electrical technology as a whole, with independent intellectual property rights, one of the most advanced universal horizontal balancing machine. Because of its simple operation, stable performance and accurate detection accuracy, it is widely used in motor, fan, water pump, printing, paper, textile machinery, internal combustion engine, electronics, machine tools and aerospace industries.

YLD-100 single-sided vertical balancing machine is a more advanced hard bearing balancing machine. It is suitable for the calibration of dynamic balancing machine for automobile and motorcycle accessories. Such as clutch pressure plate, flywheel, gear, pulley and other disc parts. This series of equipment has standard, type A, type B and other three configurations. Type A configuration is equipped with a de-reuse bench drill; Type B configuration is equipped with a de-reuse bench drill and a chip removal vacuum cleaner, which is an ideal supporting equipment on the production line of professional manufacturers of disc rotors and auto and motorcycle accessories.

YLD-50 vertical balancing machine is a more advanced vertical hard bearing balancing machine. It is suitable for the calibration of dynamic balancing machine for automobile and motorcycle accessories. Such as clutch pressure plate, flywheel, gear, pulley and other disc parts. This series of equipment has standard, type A, type B and other three configurations.

The YRD-200 drive shaft balancing machine is a special balancing machine for dynamic balance check of the drive shaft. For the large rotor quality of the workpiece, the balance speed and balance accuracy requirements are high transmission shaft workpiece for dynamic balance detection, such as large industrial transmission shaft, large truck transmission shaft.

The YRD-100B/YRD-160 type drive shaft balancing machine is a hard support structure, and the drive head drives the drive shaft to run, which is a universal two-swing frame. It is suitable for the single drive shaft dynamic balance of cars and trucks. This model is widely used in the drive shaft maintenance industry.

< 1234...11 >

Free consultation professional answer
Leave your contact information and we will contact you as soon as possible for free professional answers.

Submit Message
Customer Service